Technical Parameters

Power Supply	DC24V, AC24V, AC110V, AC220V, AC380V
Standard Torque/Time	400 Nm/30 S
Optional Torque/Time	200Nm/15S, 400Nm/60S
Rotation Angle Range	Adjustable from 0 to 90 degrees
Motor power	DC24V：70W/5.13A AC24V：90W/6.80A AC110V：90W/1.12A AC220V：90W/0.57A AC380V：40W/0.29A
Control Circuit	Type A/B/C/D/E/F/G/H
Weight	9.5Kg
Insulation Resistance	DC24V/AC24V： 100MΩ/250VDC AC110V/AC220V/AC380V： 100MΩ/500VDC
Withstand Voltage	DC24V/AC24V: 500VAC for 1 minute
Water Proof Level	IP67
Installation	360 ° installation at any angle
Electrical Interface	G1/2 waterproof cable connector: one power line and one signal line each
Working Temperature	-25℃ ~ +55℃
Optional Function	Over torque protection, dehumidification heater, convex indicator, operating handwheel

Dimensions

E - Modulação com uma unidade de controle

Connecting Details:

F - Com uma unidade de posicionamento

Connecting Details:

C - Com um potenciômetro de 1KΩ/500Ω

Atuador de controle para abrir ou fechar com K
A posição da válvula em tempo real será enviada como um valor de resistência do potenciômetro.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P5. The resistance value between P4 and P5 will become higher as actuator opening the valve, while the value between P5 and P6 will become lower.
P6 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P7.

D - Com um potenciômetro e feedback de posição final

Atuador de controle para abrir ou fechar com K
A posição da válvula em tempo real será enviada como um valor de resistência do potenciômetro.
O terminal de saída de posição final ABERTO/FECHAR enviará o evento como um sinal passivo quando a posição final for atingida.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
P7 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P8. The resistance value between P7 and P8 will become higher as actuator opening the valve, while the value between P8 and P9 will become lower.
P9 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P12.

A - Com 2 saídas de sinal de posição final ativas

Atuador de controle para abrir ou fechar com K
O terminal de saída da posição final ABERTO/FECHAR enviará o evento como um sinal ativo de 220 VCA quando a posição final for atingida.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P5 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of open.
P6 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of close.
Connect earth to P7.

B - Com 2 interruptores passivos de posição final

Atuador de controle para abrir ou fechar com K
O terminal de saída de posição final ABERTO/FECHAR enviará o evento como um sinal passivo quando a posição final for atingida.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

G - Motor CC com 2 interruptores de posição final

O atuador de controle abre ou fecha de acordo com a direção da alimentação elétrica entre os terminais 1 e 2.
O terminal de saída de posição final ABERTO/FECHAR enviará o evento como um sinal passivo quando a posição final for atingida.

Connecting Details:

Connecting DC24V+ to P1 and DC24V- to P2 to close the valve.
Connecting DC24V+ to P2 and DC24V- to P1 to close the valve.
P3 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P4 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P5 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

H - Motor trifásico de 380 VCA com 2 interruptores de posição final

Atuador de controle para abrir ou fechar por meio de um inversor externo, alterando assim a fase da energia fornecida.
O terminal de saída de posição final ABERTO/FECHAR enviará o evento como um sinal passivo quando a posição final for atingida.

Connecting Details:

Connecting a 3 phase AC380V inverter output to P1, P2 and P3, then the actuator can be controlled to open or close the valve by change the 3 phase order.
Connecting AC380V neutral to N(P4).
P5 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of CLOSE and disconnected from N(P4) after actuator reached end-position of CLOSE.
P6 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of OPEN and disconnected from N(P4) after actuator reached end-position of OPEN.
P7 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P8 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P9 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P12.

Observação:

O circuito dentro da caixa tracejada é o circuito interno do atuador. Já o circuito externo demonstra a conexão elétrica para utilização do atuador.
Caso tenha outros requisitos específicos sobre a conexão do circuito, não hesite em contatar nosso suporte técnico.