Technical Parameters

Power Supply	DC24V, AC24V, AC110V, AC220V, AC380V
Time/torque	2S/25Nm, 4S/50Nm, 8S/80Nm
Rotation Angle	Adjustable from 0 to 90 degrees
Motor Power/Current	DC24V: 25W/6.0A AC24V: 25W/2.12A AC110V: 25W/0.57A AC220V: 25W/0.35A AC380V: 15W/0.10A
control circuit	G-type/A-type/B-type/H-type
Weight	4.5Kg
Insulation Resistance	DC24V: 100MΩ/250VDC AC24V~380V: 100MΩ/500VDC
Withstand Voltage	DC/AC24V: 500VAC for 1 minute
Water Proof Level	IP67
Installation	360 ° installation at any angle
Electrical Interface	G1/2 waterproof cable joint
Working Temperature	-25℃ ~ +55℃
Optional Function	Dehumidification heater, convex indicator, handwheel

Dimensions

E - Juhtseadmega moduleerimine

Connecting Details:

F - Positsioneerimisüksusega

Connecting Details:

C - 1KΩ/500Ω potentsiomeetriga

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P5. The resistance value between P4 and P5 will become higher as actuator opening the valve, while the value between P5 and P6 will become lower.
P6 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P7.

D - Potentsiomeetri ja lõppasendi tagasisidega

Juhtige ajamit avamiseks või sulgemiseks K-ga
Reaalajas klapi asend saadetakse välja potentsiomeetri takistusväärtusena.
Lõppasendi AVATUD/SULETUD väljundklemm saadab sündmuse passiivse signaali kujul, kui lõppasend on saavutatud.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
P7 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P8. The resistance value between P7 and P8 will become higher as actuator opening the valve, while the value between P8 and P9 will become lower.
P9 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P12.

A - 2 aktiivse lõppasendi signaaliväljundiga

Juhtige ajamit avamiseks või sulgemiseks K-ga
Lõppasendi AVATUD/SULETUD väljundklemm saadab sündmuse 220 V AC aktiivse signaalina, kui lõppasend on saavutatud.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P5 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of open.
P6 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of close.
Connect earth to P7.

B - Kahe passiivse lõppasendi lülitiga

Juhtige ajamit avamiseks või sulgemiseks K-ga
Lõppasendi AVATUD/SULETUD väljundklemm saadab sündmuse passiivse signaali kujul, kui lõppasend on saavutatud.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

G - kahe lõppasendi lülitiga alalisvoolumootor

Juhtige ajamit avama või sulgema toitepinge suuna abil klemmide 1 ja 2 vahel
Lõppasendi AVATUD/SULETUD väljundklemm saadab sündmuse passiivse signaali kujul, kui lõppasend on saavutatud.

Connecting Details:

Connecting DC24V+ to P1 and DC24V- to P2 to close the valve.
Connecting DC24V+ to P2 and DC24V- to P1 to close the valve.
P3 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P4 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P5 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

H - 3-faasiline 380 V vahelduvvoolumootor kahe lõppasendi lülitiga

Välise inverteri abil saab ajamit avada või sulgeda, et muuta toitepinge faasi.
Lõppasendi AVATUD/SULETUD väljundklemm saadab sündmuse passiivse signaali kujul, kui lõppasend on saavutatud.

Connecting Details:

Connecting a 3 phase AC380V inverter output to P1, P2 and P3, then the actuator can be controlled to open or close the valve by change the 3 phase order.
Connecting AC380V neutral to N(P4).
P5 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of CLOSE and disconnected from N(P4) after actuator reached end-position of CLOSE.
P6 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of OPEN and disconnected from N(P4) after actuator reached end-position of OPEN.
P7 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P8 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P9 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P12.

Märkus:

Katkendliku kasti sees olev vooluring on ajami sisemine vooluring. Väljas olev vooluring aga demonstreerib ajami elektriühendust.
Kui teil on ühendusahela kohta muid erinõudeid, võtke julgelt ühendust meie tehnilise toega.