Technical Parameters

Explosion Proof Grade	Exd II CT4Gb
Power Supply	DC24V, AC24V, AC110V, AC220V, AC380V
Standard Torque/Time	100 Nm/30 s
Optional Torque/Time	50Nm/15S, 100Nm/60S
Rotation Angle Range	Adjustable from 0 to 90 degrees
Motor Power/Current	DC24V: 25W/2.20A AC24V: 25W/2.12A AC110V: 25W/0.57A AC220V: 15W/0.30A AC380V: 25W /0.10A
Control Circuit	Type A/B/C/D/E/F/G/H
Weight	5.0kg
Insulation Resistance	DC24V/AC24V: 100MΩ/250VDC AC110V/AC220V/AC380V: 100MΩ/500VDC
Withstand Voltage	DC24V/AC24V: 500VAC for 1 minute
Water Proof Level	IP68
Installation	360 ° installation at any angle
Electrical Interface	2-M20x1.5 explosion-proof plug, users should install corresponding explosion-proof cable connectors according to the selected cable during use
Working Temperature	-20℃~+60℃
Optional Function	Dehumidification heater

Dimensions

E - Modulación con una unidad de control

Connecting Details:

F - Con una unidad de posicionamiento

Connecting Details:

C - Con un potenciómetro de 1 kΩ/500 Ω

Controlar el actuador para abrir o cerrar con K
La posición de la válvula en tiempo real se enviará como un valor de resistencia del potenciómetro.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P5. The resistance value between P4 and P5 will become higher as actuator opening the valve, while the value between P5 and P6 will become lower.
P6 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P7.

D - Con un potenciómetro y retroalimentación de posición final.

Controlar el actuador para abrir o cerrar con K
La posición de la válvula en tiempo real se enviará como un valor de resistencia del potenciómetro.
El terminal de salida de la posición final APERTURA/CIERRE enviará el evento como una señal pasiva cuando se alcance la posición final.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
P7 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P8. The resistance value between P7 and P8 will become higher as actuator opening the valve, while the value between P8 and P9 will become lower.
P9 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P12.

A - Con 2 salidas de señal de posición final activas

Controlar el actuador para abrir o cerrar con K
El terminal de salida de la posición final APERTURA/CIERRE enviará el evento como una señal activa de 220 VCA cuando se alcance la posición final.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P5 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of open.
P6 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of close.
Connect earth to P7.

B - Con 2 interruptores de posición final pasivos

Controlar el actuador para abrir o cerrar con K
El terminal de salida de la posición final APERTURA/CIERRE enviará el evento como una señal pasiva cuando se alcance la posición final.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

G - Motor de CC con 2 interruptores de posición final.

Controla el actuador para que se abra o se cierre mediante la dirección de la alimentación eléctrica entre los terminales 1 y 2.
El terminal de salida de la posición final APERTURA/CIERRE enviará el evento como una señal pasiva cuando se alcance la posición final.

Connecting Details:

Connecting DC24V+ to P1 and DC24V- to P2 to close the valve.
Connecting DC24V+ to P2 and DC24V- to P1 to close the valve.
P3 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P4 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P5 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

Motor H - trifásico de 380 VCA con 2 interruptores de posición final.

Controlar el actuador para abrirlo o cerrarlo mediante un inversor externo para cambiar la fase de la alimentación eléctrica.
El terminal de salida de la posición final APERTURA/CIERRE enviará el evento como una señal pasiva cuando se alcance la posición final.

Connecting Details:

Connecting a 3 phase AC380V inverter output to P1, P2 and P3, then the actuator can be controlled to open or close the valve by change the 3 phase order.
Connecting AC380V neutral to N(P4).
P5 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of CLOSE and disconnected from N(P4) after actuator reached end-position of CLOSE.
P6 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of OPEN and disconnected from N(P4) after actuator reached end-position of OPEN.
P7 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P8 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P9 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P12.

Nota:

El circuito dentro del recuadro punteado es el circuito interno del actuador. El circuito exterior muestra la conexión eléctrica para el funcionamiento del actuador.
Si tiene otros requisitos específicos sobre la conexión del circuito, no dude en ponerse en contacto con nuestro servicio de asistencia técnica.