Technical Parameters

Power Supply	DC24V, AC24V, AC110V, AC220V, AC380V
Standard Torque/Time	600 Nm/45 s
Rotation Angle Range	Adjustable from 0 to 90 degrees
Motor power	DC24V：70W/6.04A AC24V：90W/6.80A AC110V：90W/1.18A AC220V：90W/0.6A AC380V：40W/0.29A
Control Circuit	Type A/B/C/D/E/F/G/H
Weight	10Kg
Insulation Resistance	DC24V/AC24V： 100MΩ/250VDC AC110V/AC220V/AC380V： 100MΩ/500VDC
Withstand Voltage	DC24V/AC24V: 500VAC for 1 minute
Water Proof Level	IP67
Installation	360 ° installation at any angle
Electrical Interface	G1/2 waterproof cable connector: one power line and one signal line each
Working Temperature	-25℃ ~ +55℃
Optional Function	Over torque protection, dehumidification heater, convex indicator, operating handwheel

Dimensions

E - Modulation avec une unité de contrôle

Connecting Details:

F - Avec une unité de positionnement

Connecting Details:

C - Avec un potentiomètre 1KΩ/500Ω

Actionneur de commande pour ouvrir ou fermer avec K
La position de la vanne en temps réel sera transmise sous forme de valeur de résistance du potentiomètre.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P5. The resistance value between P4 and P5 will become higher as actuator opening the valve, while the value between P5 and P6 will become lower.
P6 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P7.

D - Avec un potentiomètre et un retour de position finale

Actionneur de commande pour ouvrir ou fermer avec K
La position de la vanne en temps réel sera transmise sous forme de valeur de résistance du potentiomètre.
La borne de sortie de la position finale OUVERTE/FERMÉE enverra l'événement sous forme de signal passif lorsque la position finale sera atteinte.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
P7 is the low side of potentiometer that is normally connected to signal GND.
Connecting signal input of control system to P8. The resistance value between P7 and P8 will become higher as actuator opening the valve, while the value between P8 and P9 will become lower.
P9 is the high side of potentiometer that is normally connected to signal power.
Connect earth to P12.

A - Avec 2 sorties de signal de position finale actives

Actionneur de commande pour ouvrir ou fermer avec K
La borne de sortie de la position finale OUVERTE/FERMÉE enverra l'événement sous la forme d'un signal actif de 220 V CA lorsque la position finale sera atteinte.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P5 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of open.
P6 is end-position OPEN terminal which will output a AC220V source which can be used to drive an Indication light when actuator reached end-position of close.
Connect earth to P7.

B - Avec 2 interrupteurs de fin de course passifs

Actionneur de commande pour ouvrir ou fermer avec K
La borne de sortie de la position finale OUVERTE/FERMÉE enverra l'événement sous forme de signal passif lorsque la position finale sera atteinte.

Connecting Details:

Connecting AC85-220V supply power neutral to P1.
Switch AC85-220V line to CLOSE(P2) to close the valve
Switch AC85-220V line to OPEN(P3) to open the valve.
P4 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P5 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P6 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

Moteur à courant continu G avec 2 interrupteurs de fin de course

Actionneur de commande pour s'ouvrir ou se fermer en fonction du sens d'alimentation entre les bornes 1 et 2
La borne de sortie de la position finale OUVERTE/FERMÉE enverra l'événement sous forme de signal passif lorsque la position finale sera atteinte.

Connecting Details:

Connecting DC24V+ to P1 and DC24V- to P2 to close the valve.
Connecting DC24V+ to P2 and DC24V- to P1 to close the valve.
P3 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P4 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P5 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P7.

Moteur triphasé 380 V CA H avec 2 interrupteurs de fin de course

Actionneur de commande permettant l'ouverture ou la fermeture par un onduleur externe afin de modifier la phase de l'alimentation électrique.
La borne de sortie de la position finale OUVERTE/FERMÉE enverra l'événement sous forme de signal passif lorsque la position finale sera atteinte.

Connecting Details:

Connecting a 3 phase AC380V inverter output to P1, P2 and P3, then the actuator can be controlled to open or close the valve by change the 3 phase order.
Connecting AC380V neutral to N(P4).
P5 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of CLOSE and disconnected from N(P4) after actuator reached end-position of CLOSE.
P6 is used for cooperating with an external switch to control the inverter 3 phase order. This terminal is connected to N(P4) when actuator is not in end-position of OPEN and disconnected from N(P4) after actuator reached end-position of OPEN.
P7 is the COM for passive contact signal of end-position OPEN/CLOSE which is normally connected to signal GND.
P8 is end-position OPEN terminal which will be connected to COM when actuator reached end-position of open.
P9 is end-position CLOSE terminal which will be connected to COM when actuator reached end-position of close.
Connect earth to P12.

Note:

Le circuit à l'intérieur du cadre en pointillés représente le circuit interne de l'actionneur. Le circuit extérieur illustre le branchement électrique nécessaire à l'utilisation de l'actionneur.
Si vous avez d'autres exigences spécifiques concernant le raccordement du circuit, n'hésitez pas à contacter notre assistance technique.